Bw16 Bw16-Kit Bw12 Rtl8710bx Bw14 Rtl8720dn Rtl8710af Bw15 Nodemcu Serial Port To Wifi Wireless WIF

the Characteristics Of
por 802.11a/b/g/n 11, 2.4ghz or 5ghz
por HT20/HT40 Mode
por Low Power Beacon Listening Mode, Low Power Receive Mode, Low Power Suspend Mode
install AES/DES/SHA Harare Engine
trustzone-m port, Start-up Security port
port for Debug Port Access Protection and Disabg Modes
port for BLE and Bt5.0
bluetooth por High Power Mode (7dbm, Sharing the Same PA as Wi-fi)
wi-fi and BT Share the Same Antenna
port STA/AP/STA+AP Working Mode
simple Config (APP) port Android, IOS One-cli Network Configuration
local Upgrade and Remote Firmware Upgrade (FOTA) port for Port Service
model
prc6 Envelopepaper Size
prc6 Envelopepaper Size
prc6 Envelopepaper Size
prc6 Envelopepaper Size
w_ith More Recently Played Tras Firstquery-sort
pcb
pcb
pcb/ipex
pcb
mor Cet
rtl8710bx
rtl8710bx
rtl8720dn
rtl8710af
katan
24*16*3
50.5*29.2*3.3
24*16*3
24*16*0.8
use Board Entry
of BW16:
I. Overview of BW16
BW16 is A Dual-band Wi-fi+ Bluetooth Soc Module Built on the Basis of RTL8720DN. BW16 por Dual-band (2.4ghz or 5ghz) WLAN and Low-power Bluetooth
5.0; It Combines High-performance MCU, Low-power MCU (cortex-m0), WLAN (802.11a/b/g/n), Bluetooth Baseband and RF Baseband, and Provides A Set of Configurable GPIO Por for Control of Various Perieral Devices. BW16 Also Provides Internal Storage, por Simple Appliion , and Fully Functional Wi-fi and BT 5.0 Protocols.
[unk]. Module/ Board Wiring
2.1 Wiring Modules
there Are Two Series of Por in Module BW16. One is the AT Serial Port (the Default Baud Rate is 38400), Used for Receiving and Receiving AT Instruction. the Same Port Numbers Are AT_TX and AT_RX. One is the LOG Serial Port (baud Rate 115200), Used to Print Logs and Download
firmware, for Port Numbers Log_tx,log_rx.
after Getting the Module, the First Thing is to Connect 3.3V,GND,LOG_TX,LOG_RX, and Send Instructions to the LOG Serial Port AC=0 to Switch to the OTA1 Image, Otherwise the Module and Serial Port Part Sends Instructions
of Actions That Don’t Respond.
2.2 Board Wiring
the Board’s USB Interface Corresponds to the BW16 Module’s AT Serial Port.
log Serial Port as Shown Below, Used to Print LOG, the Debit ase is Recommended to Connect Out
8546; Network
prc6 Envelopepaper Size
3.1 Simple Config Distribution Network
(1). Install Simpleconfigwizard_v115.apk on the Mobile one (the Version is Older and May Not Be Compatible with the Mobile one System. If You Can’t Use It, Switching to the Bluetooth Network)
(2). Wifi Has A Mobile one Connection to See the Network
(3) Cli to Configure the New Device
(4) Select
network to Store
(5) Enter the Wifi Pas and Cli the K
(6) Send SIMPLE CONFIG Distribution Network Instruction to BW16 Module
(7) Cli to Skip Mobile APP
(8) It is Currently Entering the Distribution Network Process
(9) After the Success of the Distribution Network, It is Shown As
sumusunode
3.2 Bluetooth Network Matching
(1) I-install Ang Wificonf